When it comes to ordering custom-made window treatments, it should be an experience that would help you take your interior design to the next level, but faulty measurement could easily ruin this wonderful experience. Taking the accurate dimension before placing your order will determine whether your project will result in success or failure.
In considering your next window treatment, by working with a top curtains company in New York such as Supreme Shades, you can be assured of getting the best advice as well as precise custom curtain construction that will fit your particular design.
Image Source: Pinterest
Measuring Only the Glass and Not the Whole Casing
When it comes to measuring new window treatments, one of the mistakes that people make at home is taking dimensions only for the glass window and ignoring everything else around it.
Measuring the glass window will not only give you the incorrect measurement but will also make sure that the windows appear much smaller than they are because the curtain rod has been hung very close to the glass window.
In order to make a full and luxurious look, your measurements will have to go beyond the outside dimensions of the window casing. Going four to eight inches beyond the frame on either side will allow the material to tuck against the wall when fully drawn, letting more light in to give the room a larger and brighter look.
See also: Regain Control of Your Life With Drug Addiction TreatmentÂ
Curtain Rod Installed Too Low Above the Frame
A common error in curtain rod installation is installing the curtain rod right above the window casing. Doing this makes the ceiling seem lower than it really is. Since the curtains are too low, it squeezes the wall space and makes the entire room look smaller and older.
Designers place curtain rods much higher up for the effect of dramatic vertical height. Before you take measurements vertically, consider the height at which you want to mount your rod, which should ideally be placed half way between the top of the window trim and ceiling trim.
Panels ordered on this raised height will make your ceiling look higher and will give an effect of high ceilings. To get advice about the right placement height for your specific ceiling, consult a good curtains company in New York.
Not Taking into Account Header Type and Hardware
Not considering the kind of header as well as hardware for mounting the panels can result in length variations after installing the panels on the rod. Different types of headers like pinch pleat, grommet, rod pocket and ring top have different hanging patterns on the rod and vary in terms of how close they hang to the mounting hardware.
A clip ring adds two to three inches to the drop below the rod. This implies that a regular-sized panel would pool on the floor if the ring drop is not deducted from the total length measurement. But, a grommet top panel extends past the rod line, thus, necessitating sufficient space between the hardware and the ceiling or crown molding.
Ignoring Wall Projections, Obstructions, and Deep Trims
Measuring vertically without regard to physical barriers results in curtain fabric that hangs against the wall projections rather than dropping straight to the floor. While taking measurements, one should look out for any architectural features projecting outward from the wall.
Extended mounting brackets guarantee that the curtain rod projects forward enough to allow for deep window sills or radiators. A simple talk with an expert in a curtain company in New York will help determine hardware projections before your custom panels are tailored.
Making Use of a Soft Cloth or Plastic Tape in Place of a Steel Tape
When using a pliable fabric tape measure, you may be making the fastest way for mistakes to occur in your measurement of window dimensions. The soft cloth or plastic tapes tend to stretch out and become slackened when held against long distances on the wall, causing inaccuracies in the reading which will affect your whole order.
For precise window dimensions, you should make use of a sturdy steel tape measure. Ensure that the tape remains taut against the wall or window as you write down the measurements. Measuring each window twice and recording them down to the nearest eighth of an inch ensures that there is no guessing about the exact dimension of the window.
Assuming that Matching Windows Have Exactly the Same Dimension
It may seem like windows that match in terms of design in your living room or bedroom would have identical dimensions. However, this is not usually the case as minor differences in construction of your house usually lead to minor variations in the dimensions of seemingly identical windows.
Individually measuring all the windows will not leave you with surprises while installing them. Do not use the same measurements for all the windows; measure individually each of them. Working with a specialized curtains company in New York City will ensure that each curtain will be made according to specific window frame dimensions.
Floor Clearance and Hem Placement Mistakes
The total length of your drapes will determine the mood of the whole room. The mistake many people make is that they do not realize what kind of hemming they want to get – floating above the floor by an inch, kissing the floor surface or puddling on the rug.
Make your decision about it prior to measuring the length of the drapes. For example, for getting a tailored look, you need to add only half an inch, whereas for creating a formal mood, you need to add 2-4 inches. Taking measurements from the top of the installed rod to the floor will help you in getting your desired hemming place.
Conclusion
The avoidance of errors when taking measurements is the best thing you can do to ensure a successful outcome of your drapery installation project. Using proper equipment, taking hardware drops into account, figuring out fabric fullness correctly, and measuring each window separately ensures the success of your endeavor.
